How to make a kilt?

September 3, 2015
JPG PA253.JPG

The Ancient Kilt with lasting Pleats

This task began whenever I took place to get a few bolts of cotton fiber flannel in a vaguely navy Stuart tartan at JoAnns. It had been available for sale too. Therefore, i got myself everything.

A few of the material we made into an arisaid for myself. The rest we cut into a bit suited to a ancient kilt and fringed it. The proportions are about 6 yards 6 inches by 28 inches. I possibly could never ever get DH to put on it because he doesn't trust something which is simply pleated, wrapped across the human body, and held in the human body with only a belt.

So, I decided to give the kilt a little bit of framework in the hope i really could encourage him to wear the kilt. Ummm...DH in a kilt...oh my...

Fundamental Information About Kilts - Varieties, Yardage Required, Folding

The information listed below is perhaps all from Celtic Croft. They sell yardage when it comes to various kinds of kilts given below and they also deliver solution of permanently stitching into the pleats such that it can be done to just wrap the kilt and go.

The Great Kilt (Feileadh-Mhor)
60 inches large by 4 and 1/2 yards (The "whole nine yards" of olden days when fabric widths had been typically 30 inches.)
60 inches wide by 4 yards - up to 34 inches waist
60 inches broad by 5 yards - as much as 44 inch waist
60 ins large by 6 yards - up to 50 inch waist
Pleating the truly amazing Kilt from The Celtic Croft

Ancient Kilt (like Mel Gibson wore in Braveheart - a Phillabeg with a 2 yard sash attached)
30 ins wide by 6 yards - around 38 inches waist
30 inches wide by 9 yards - around 50 inch waistline
30 ins broad by 12 yards - 50 inch plus waists
Pleating the Ancient Kilt from Celtic Croft

The tiny Kilt (Feileadh Beag aka Phillabeg)
30 ins broad by 4 yards - to 34 inch waist
30 ins wide by 5 yards - around 44 inches waistline
30 inches broad by 6 yards - up to 50 inches waist
Pleating the tiny Kilt from Celtic Croft

The Modern Kilt
Kilt Pattern available from Folkwear
through the Celtic Croft
An online resource - Making a Kilt

Kilt Pleats

There a few methods of pleating a kilt when you're planning to completely fix the pleats into destination. Box pleats or knife pleats can be used.

Container pleats tend to be a conventional military-style. The pleats tend to be broad (three or four inches large according to the sett width associated with the tartan.) Container pleating makes use of less textile. A typical example of a box pleated Phillabeg from The Celtic Croft.

Knife pleats are more typical, as this is exactly what is usually through with a duration of plaid which pleated whenever it is worn. With permanent blade pleats, a kilt is either pleated to stripe or sett.

Below is a good example of a kilt pleated to stripe.

Click on thumbnails to see a bigger image.

Front

Back

A kilt pleated to sett.

In both varieties of pleating, leading associated with kilt is unpleated and reveals the tartan to complete benefit. In the back of the pleated-to-stripe kilt, one stripe inside tartan is emphasized because it is found at edge of each pleat. This can be another old-fashioned military-style. Not all the tartans look great pleated to stripe. In the back of the pleated-to-sett kilt, the perform of the tartan (or sett) is preserved even though the textile has been pleated

The ancient kilt I made for DH utilizes blade pleats, pleated to sett.

Measurements and Pleating Computations

DH's all-natural waistline (Note: this is NOT where guys usually put on their mundane pants.) dimension had been 40 inches. I'd him kneel on to the floor and calculated through the normal waist towards floor. This dimension had been 20 ins.

When I claimed above, the material I have to use is approximately 6 yards 6 ins (222 ins) by 28 inches. In accordance with the directions for Pleating the Ancient Kilt through the Celtic Croft, I needed seriously to allocate about 22 inches for inside apron. I place a safety pin in textile 22 inches from remaining brief side of the kilt textile to mark in which i'd start the pleating. In addition needed to allocate about 2 yards for the sash, therefore I place another safety-pin within the material 72 ins through the correct short side of the kilt fabric to mark in which i might end the pleating. This left me with about 128 ins of fabric to pleat down seriously to a space of 20 inches. I desired 1 inch revealed for each pleat. The perform of the plaid had been 5 ins, therefore for each complete pleat (the start of one pleat into the start of next pleat) 1 inches would-be exposed and 5 inches concealed. This implies I would be making between 21 and 22 pleats together with complete period of the finished pleated part could be 21 to 22 ins lengthy. I made a decision to accomplish simply 21 pleats and allow the sash be slightly longer.

Making the Kilt

After doing some test pleats, I recognize i shall have better control over the revealed textile on the exterior or right side associated with kilt easily flip everything around and pleat from the right side regarding the fabric.

Source: www.karen.htmlcreators.com
RELATED VIDEO
Learn how to make your own Kilt pin in minutes!
Learn how to make your own Kilt pin in minutes!
Scotland. How to make a kilt
Scotland. How to make a kilt
how to make a scottish great kilt
how to make a scottish great kilt
RELATED FACTS
Share this Post